国产大爆乳大爆乳在线播放,国产高清女同学巨大乳在线观看,国产波霸爆乳一区二区

            <th id="z28gn"><option id="z28gn"></option></th>
            1. <strike id="z28gn"><video id="z28gn"></video></strike>

              • 電話:0531-87199680
              • 傳真:0531-87119680
              • 銷售熱線:400-685-1687
              • 地址:濟南市104國道邵西
              • 潤鑫工業園
              新聞中心當前位置:首頁-新聞中心
                母線加工機的保養常識分析

                數控母線加工機是一種自動化程度較高,結構較復雜的先進加工設備,是企業的重點、關鍵設備。要發揮數控設備的高效益,就必須正確的操作和精心的維護,才能保證設備的利用率。正確的操作使用能夠防止機床非正常磨損,避免突發故障;做好日常維護保養,可使設備保持良好的技術狀態,延緩劣化進程,及時發現和消滅故障隱患,從而保證安全運行。

                CNC bus processing machine is a high degree of automation, advanced processing equipment with complex structure, is the key, key equipment. To play a high efficiency of numerical control equipment, it must be the correct operation and careful maintenance, to ensure the equipment utilization rate. The correct operation can prevent the machine non normal wear and tear, avoid sudden fault; do daily maintenance, can make the equipment keep good technical condition, delay the deterioration process, timely find and eliminate the hidden trouble, so as to ensure safe operation.

                1、數控設備使用中應注意的問題

                Attention should be paid to the use of 1, CNC equipment problems

                1.1數控設備的使用環境

                1.1 CNC equipment use environment

                為提高數控設備的使用壽命,一般要求要避免陽光的直接照射和其他熱輻射,要避免太潮濕、粉塵過多或有腐蝕氣體的場所。腐蝕氣體易使電子元件受到腐蝕變質,造成接觸不良或元件間短路,影響設備的正常運行。精密數控設備要遠離振動大的設備,如沖床、鍛壓設備等。

                In order to improve the service life of CNC equipment, general requirements to avoid direct sunlight and heat radiation, to avoid too wet, too much dust or corrosive gas places. Corrosion gas is easy to make electronic components subjected to corrosion, resulting in poor contact or element short circuit, affect the normal operation of equipment. Precision CNC equipment to be away from the great vibration of the equipment, such as punching, forging equipment etc..

                1.2電源要求

                1.2 power requirements

                為了避免電源波動幅度大(大于±10%)和可能的瞬間干擾信號等影響,數控設備一般采用專線供電(如從低壓配電室分一路單獨供數控機床使用)或增設穩壓裝置等,都可減少供電質量的影響和電氣干擾。

                In order to avoid large fluctuations (power greater than ± 10%) effects and possible interference signal, CNC equipment generally use the special power supply (such as from a single low voltage power distribution room for numerical control machine tool) or provided with a voltage stabilizing device, can reduce the quality of power supply and electrical interference.

                1.3操作規程

                1.3 operating rules

                母線加工機操作規程是保證數控機床安全運行的重要措施之一,操作者一定要按操作規程操作。機床發生故障時,操作者要注意保留現場,并向維修人員如實說明出現故障前后的情況,以利于分析、診斷出故障的原因,及時排除。另外,數控機床不宜長期封存不用,購買數控機床以后要充分利用,尤其是投入使用的第一年,使其容易出故障的薄弱環節盡早暴露,得以在保修期內得以排除。在沒有加工任務時,數控機床也要定期通電,最好是每周通電1-2次,每次空運行1小時左右,以利用機床本身的發熱量來降低機內的濕度,使電子元件不致受潮,同時也能及時發現有無電池報警發生,以防止系統軟件、參數的丟失。

                Operating rules is one of the important measures to guarantee the safe operation of CNC machine tool, the operator must operate according to the operating rules. Failure of machine tools, the operator should pay attention to preserve the site, and to repair personnel accurately described the situation before and after the failure, in order to facilitate the analysis, diagnose the cause, timely elimination. In addition, numerical control machine tool should not be long-term storage without, after the purchase of CNC machine tools to make full use of, especially in the first year and put into use, which is easy to be a weak link fault as soon as possible exposure, able to exclude in the warranty period. In the absence of processing tasks, CNC machine tools are also regularly energized, preferably a weekly energized 1-2 times, each empty run for about 1 hours, using heat machine itself to reduce the humidity inside the machine, making electronic components not to be affected with damp, also can find no battery alarm occurs, to preventing loss system software, parameters.

              国产大爆乳大爆乳在线播放,国产高清女同学巨大乳在线观看,国产波霸爆乳一区二区